Thank you for choosing Galileosky
Tracking device setup
1. Insert SIM card-
Remove SIM holder using a thin needle
-
Insert SIM card (nano SIM) into the holder of the device as shown below
-
Insert SIM holder back
*for models with external antennas
ATTENTION! No external power supply and discharged internal battery will cause loss of connection with the server
-
Connect the power wires to the VCC and GND inputs (see the Tracking device pinout at the back of the device)
-
Connect the connector to the device
-
Connect an external 9...39V power supply. The device can be powered from a constant voltage of 9V and up to 39 V (with a current of at least 1A)
Configurator settings
1. Download Configurator-
Download the Configurator app
-
Setup and launch the app
-
Connect your device to computer using a micro-USB cable (not included in the package)
-
Open the "Configurator" app to setup the device
-
Wait for the device to be loaded in the configurator
-
Check whether the device is receiving coordinates
The GPS/GLONASS antenna head (for versions with external antennas) or the entire device body (for versions with internal antennas) must be on a line of sight before the test.3. Set up data transmission to the monitoring software
-
Select the suitable software to receive information from the device and display the track, if you are not registered in the monitoring software yet.
-
Create an account or object with the device data (the configuration depends on the selected monitoring software)
-
Enter the IP address or domain name and port for the Primary server
-
Fill out the APN parameters according to the preferred operator
-
If you need to set up the data transmission via WiFi connection
Then fill out the:
— network name
— encryption type
— network access password
-
If necessary, the frequency of recording/sending track points to the server can be changed as well as the quality parameters of the track drawing
-
Click the "Apply" button
Connection Check
If the previous operations have been completed, check that the device transmits the data to the selected monitoring software
-
Go to the Device tab
-
In the Status box, make sure that the GPRS session and the Primary server lines are highlighted in red
Tracking device setup
1. Insert SIM card-
Remove SIM holder using a thin needle
-
Insert SIM card (nano SIM) into the holder of the device as shown below
-
Insert SIM holder back
Configurator settings
1. Download Configurator- Download the Configurator app
- Setup and launch the app
-
Connect your device to computer using a micro-USB cable (not included in the package)
-
Open the "Configurator" app to setup the device
-
Wait for the device to be loaded in the configurator
-
Select the suitable software to receive information from the device and display the track, if you are not registered in the monitoring software yet.
-
Create an account or object with the device data (the configuration depends on the selected monitoring software)
-
Enter the IP address or domain name and port for the Primary server
-
Fill out the APN parameters according to the preferred operator
5. Setting the track drawing parameters
-
If necessary, the frequency of recording/sending track points to the server can be changed as well as the quality parameters of the track drawing
-
Click the "Apply" button
-
Connect the device to the vehicle by plugging it into the OBDII socket
Tracking device setup
1. Insert SIM card-
Insert the SIM card (micro SIM) into the holder according to the information on the back of the device until it slightly clicks into place
ATTENTION! No external power supply and discharged internal battery will cause loss of connection with the server
-
Connect the power wires to the VCC and GND inputs (see the Tracking device pinout at the back of the device)
-
Connect the connector to the device
-
Connect an external 9...39V power supply. The device can be powered from a constant voltage of 9V and up to 39 V (with a current of at least 1A)
Configurator settings
1. Download Configurator-
Download the Configurator app
-
Setup and launch the app
-
Connect your device to computer using a micro-USB cable (not included in the package)
-
Open the "Configurator" app to setup the device
-
Wait for the device to be loaded in the configurator
-
Check whether the device is receiving coordinates
The GPS/GLONASS antenna head (for versions with external antennas) or the entire device body (for versions with internal antennas) must be on a line of sight before the test.3. Set up data transmission to the monitoring software
-
Select the suitable software to receive information from the device and display the track, if you are not registered in the monitoring software yet.
-
Create an account or object with the device data (the configuration depends on the selected monitoring software)
-
Enter the IP address or domain name and port for the Primary server
-
Fill out the APN parameters according to the preferred operator
5. Setting the track drawing parameters
-
If necessary, the frequency of recording/sending track points to the server can be changed as well as the quality parameters of the track drawing
-
Click the "Apply" button
-
To set up the connection via Iridium correctly, it is necessary to read the following manual
Connection Check
If the previous operations have been completed, check that the device transmits the data to the selected monitoring software
-
Go to the Device tab
-
In the Status box, make sure that the GPRS session and the Primary server lines are highlighted in red
