Configurator

• New firmware 2.7 for devices Galileosky 10 is added.
• New firmware 47.13 (release-candidate) for devices Galileosky 7x is added.
• New firmware 27.11 for devices Galileosky 7.0, OBD-II is added.
• New firmware 27.12 for devices Galileosky BaseBlock is added.

• Issue with displaying of Signaling settings for Galileosky 7.0 devices is fixed.
• Absence of "advertising" packets "raw" data in case if the receiver is Galileosky XS is fixed.
• Issue with exporting of the archive from the microSD card on the Data tab when connected via bluetooth is fixed.

• File sync system: limit of files depth is removed, uploading is optimized.
• Command FIXTERM for binding 1-Wire thermometers to fields in data sending protocol is added.

• Coordinate filtering is fixed.
• Detection of GNSS antenna connection is fixed.
• Frequency counting at the inputs is fixed.
• Updating coordinates based on LBS data is fixed.
• Updating of coordinates after exposure to jamming is fixed.
• Autodetection of CAN bus speed is fixed.
• Issues in the ROMDelete, ROMRead and ROMWrite functions are fixed.
• Automatic disk opening in the absence of SD\EMMC support is fixed.
• Operation of the TagWriteBegin and TagWriteEnd EasyLogic functions for tag numbers greater than 255 is fixed.
• Issue that caused the WiFi Hub to reboot is fixed.

• File sync system: limit of files depth is removed, uploading is optimized.
• Command FIXTERM for binding 1-Wire thermometers to fields in data sending protocol is added.

• Coordinate filtering is fixed.
• Detection of GNSS antenna connection is fixed.
• Frequency counting at the inputs is fixed.
• Updating coordinates based on LBS data is fixed.
• Updating of coordinates after exposure to jamming is fixed.
• Autodetection of CAN bus speed is fixed.
• Issues in the ROMDelete, ROMRead and ROMWrite functions are fixed.
• Automatic disk opening in the absence of SD\EMMC support is fixed.
• The issue causing configuration reset is fixed.
• Operation of the TagWriteBegin and TagWriteEnd EasyLogic functions for tag numbers greater than 255 is fixed.
• Issue that caused the WiFi Hub to reboot is fixed.

• User interface DUT Escort (RS485, Bluetooth) is optimized.
• The issue with displaying of CAN settings downloaded from the configuration file is fixed.

• New firmware 2.5 for devices Galileosky 10 is added.
• New firmware 47.11 (release-candidate) for devices Galileosky 7x is added.

• The display of raw data on the CAN scanner tab for PCs with small displays is corrected.
• Delay in receiving data in the CAN scanner is fixed.
• The issue with displaying settings on the Modbus tab.

• Operation with the GNSS module is fixed.
• Writing to tags from Easy Logic scripts is fixed.

• New firmware 2.4 for devices Galileosky 10 is added.
• New firmware 47.10 (release-candidate) for devices Galileosky 7x is added.

• Program crash during working on the EasyLogic tab is fixed.
• The issue with adding and setting filters on the J1939DA Protocol tab is fixed.

• Operation with 2G modems is improved.
• Coordinate duplication is fixed.
• Parsing of J1939DA messages is fixed.
• Automatic disk opening without SD card is fixed.

• Operation with 2G modems is improved.
• Processing of SD Card ejection is fixed.
• Coordinate duplication is fixed.
• Automatic disk opening without SD card is fixed.

• New firmware 2.2 for devices Galileosky 10 is added.
• New firmware 47.8 (release-candidate) for devices Galileosky 7x is added.
• Support for ISOBUS parameters in the CAN Scanner tab in the J1939DA Protocol section is added.
• Automated diagnostic data collection for Galileosky 7x and 10 devices has been modified.

ч

• The ENSCRIPTDEFRAG command to defragment the script storage when starting the device is added.
• In this firmware, the function of collecting diagnostic information is added.
• Support for the ISOBUS protocol is added.
• Command "WIEGANDCFG" to configure Wiegand parameters is added.
• Automatic request of the maximum MTU size during BLE connection is added.

• Stability and performance is improved.
• Device reboot when loading a file with zero size via WebDav is fixed.
• Error in accessing SD/eMMC when connecting the device to a computer is fixed.
• Cleaning SPN tags in case of lack of data in the CAN bus is fixed.
• Missing coordinates in case of disabled archive is fixed.
• Checking of downloaded EasyLogic script is fixed.
• GSM location is fixed.
• Sending points to a server larger than 1000 bytes is fixed.
• Parsing of SMS sender address with number type "accepted on the network" is fixed.
• Data transmission on devices with LTE support has been improved.
• Incorrect data in the 0x49 tag has been fixed.
• The issue with CAN modes when performing J1939DA scanning is fixed.
• The issue with loading identical scripts with names in different case is fixed.
• The issue of the BLE notifications stream is fixed.
• The issue with clearing a string variable when ending an EL script chain is fixed.
• The issue in initializing a string variable when there is no parameter in the command is fixed.
• Device stability when the RAM level is low is improved.
• Receiving CAN messages with the selected Easy Logic handler is enabled by default.
• Stability of CAN operation is improved.

• Missing coordinates in case of disabled archive is fixed.
• Checking of downloaded EasyLogic script is fixed.
• GSM location is fixed.
• Sending points to a server larger than 1000 bytes is fixed.
• Parsing of SMS sender address with number type "accepted on the network" is fixed.

• New firmware 47.6 (release-candidate) for devices Galileosky 7x is added.

• The issue with displaying the firmware list from the update service is fixed.

• Stability and performance is improved.
• Problem accessing SD/eMMC when connecting the device to a computer is fixed.

• New firmware 1.3 for devices Galileosky 10 is added.
• New firmware 47.5 (release-candidate) for devices Galileosky 7x is added.
• Firmware downloading from the remote firmware update service is implemented.
• The list of commands for automatic substitution on the Commands tab is updated.

• The issue with displaying the consumed RAM memory when deleting an algorithm on the "Algorithms" tab is fixed.

• The issue with caused valid coordinates to be determined for a long time is fixed.
• WebDav operating is improved.

• Stability and performance is improved.
• Device reboot when loading a file with zero size via WebDav is fixed.

• New firmware 47.03 (beta-version) for devices Galileosky 7x is added.

  *in order to improve the operation of the equipment and software, from 28.11.23., the Supplier (manufacturer) reserves the right to collect and process diagnostic information from the devices. This information will allow to react promptly and correct the operation of the devices. The Buyer has the right to disable this function in the settings according to the Instructions. The Buyer, who disables this function, confirms that he agrees to limit the Supplier's (manufacturer's) capabilities to improve the operation of the equipment and software. manual

• Uploading device configuration from a file on the Settings tab is fixed.
• The issue with loading of parameters from the terminal in FuelTarFilter block on the "Filters" tab is fixed.

• Stability of CAN operation is improved.
• Receiving CAN messages with the selected Easy Logic handler is enabled by default.
• WebDav operating is improved.

• New service firmware (Recovery) 33.18 for devices Galileosky 7x is added.
• New firmware 38.25 for devices Galileosky 7x is added.
• New firmware 47.0 (beta-version) for devices Galileosky 7x is added.

• The issue with Bluetooth scanner during remote configuration is fixed.
• The issue with CAN scanner during remote configuration is fixed.
• The issue with loading of parameters from the terminal in the TarFilter block on the "Filters" tab is fixed.

• The third parameter which controls endianess is added to the IBCFG command.
• The limitation for battery charging within the range of 9-39V of external power supply voltage is added.

• Stability of device startup while supply voltage is low is improved.
• Measuring of GNSS antenna supply voltage at device startup is fixed.
• The issue with loading identical scripts with names in different case is fixed.

• Data transmission on devices with LTE support has been improved.
• The issue with caused valid coordinates to be determined for a long time is fixed.
• Incorrect data in the 0x49 tag has been fixed.
• The issue with loading identical scripts with names in different case is fixed.
• The issue of the BLE notifications stream is fixed.
• The issue with clearing a string variable when ending an EL script chain is fixed.
• The issue in initializing a string variable when there is no parameter in the command is fixed.
• Device stability when the RAM level is low is improved.

• New user interface - File editor.

• CAN tag settings for Galileosky OBD-II devices when connecting remotely is fixed.
• IMEI display for Galileosky 5.0 devices on the Device tab is fixed.

• New firmware 38.23 for devices Galileosky 7x is added.

• Program freeze when device is disconnected during remote configuration is fixed.
• The display of the ROM value in the graphical block on the Algorithms tab is fixed.
• Color palette for RAM graphs on the Algorithms tab is changed.
• Error in setting SPN tags on the J1939DA Protocol tab is fixed.

• The volume of voice communication on devices with LTE support has been increased.
• Сlearing of CAN tags with selected EasyLogic handler is fixed.
• The issue with Eco Driving calibration is fixed.

• New firmware 1.1 for devices Galileosky 10 is added.
• New firmware 46.1 (beta-version) for devices Galileosky 7x is added.
• Support for string parameters in EasyLogic scripts is added.
• Algorithms tab for tracking information on Easy Logic algorithms is added.

• The command "SCRIPTSTORAGEINFO" to get the ROM memory size for scripts is added.
• The "GetUserArray" function is added to EasyLogic to get data from the user's array.
• Possibility to configure the network priority for devices with 3G is added.
• The functions TagWriteBegin and TagWriteEnd have been added to enable postponed writing to tags from EasyLogic.
• Feature of sending data via Iriduim right after turning on from EasyLogic is added.
• Sending acceleration data via EGTS protocol is added.
• Support for string parameters in command handlers in EasyLogic is added.
• Base64 encoding/decoding functions are added to EasyLogic.

• The issue of not displaying the status while the archive is uploading to the hub is fixed.
• Operation with SMS on some mobile network operators is fixed.
• Clearing CAN tags in case of selected EasyLogic handler for CAN is fixed.
• Resetting SPN configuration when ERASECFG command invoked is fixed.
• The volume of voice communication on devices with LTE support has been increased.
• Cleaning SPN tags in case of lack of data in the CAN bus is fixed.
• The issue with terminal reboot when frequently connecting to the TCP server is fixed.
• The issue with invalid coordinates is fixed.

• The command "SCRIPTSTORAGEINFO" to get the ROM memory size for scripts is added.
• The "GetUserArray" function is added to EasyLogic to get data from the user's array.
• Possibility to configure the network priority for devices with 3G is added.
• The functions TagWriteBegin and TagWriteEnd have been added to enable postponed writing to tags from EasyLogic.
• Feature of sending data via Iriduim right after turning on from EasyLogic is added.
• Sending acceleration data via EGTS protocol is added.
• Support for string parameters in command handlers in EasyLogic is added.
• Base64 encoding/decoding functions are added to EasyLogic.

• The issue of not displaying the status while the archive is uploading to the hub is fixed.
• Operation with SMS on some mobile network operators is fixed.
• Clearing CAN tags in case of selected EasyLogic handler for CAN is fixed.
• In CAN scanner the issue with receiving data from two CAN ports at the same time is fixed.
• The volume of voice communication on devices with LTE support has been increased.
• The issue with terminal reboot when frequently connecting to the TCP server is fixed.
• The issue with invalid coordinates is fixed.

• New firmware 27.10 for devices Galileosky 7.0, OBD-II is added.
• New firmware 27.11 for devices Galileosky BaseBlock is added.
• New firmware 38.22 for devices Galileosky 7x is added.

• Firmware version 33.17 with version 33.16 (beta version) for Galileosky 7X terminals is replaced.
• The operation of the EL script compiler is fixed.
• Error in setting filtering parameters on the Track tab is fixed.

• Periodic reboot of the device due to the non-response of the GNSS unit in self-troubleshooting if the unit was functioning normally is fixed.

• The IRIDIUMTXCFG command has been added, which allows you to disable the transmission of archive points through the Iridium modem when it is enabled from the EasyLogic algorithms.

• Periodic reboot of the device due to the non-response of the GNSS unit in self-troubleshooting if the unit was functioning normally is fixed.

• Possibility to configure the network priority for devices with 3G is added.

• New firmware 33.16 (beta-version) for devices Galileosky 7x is added.
• In the device registration dialog of the remote configuration service, a field for entering the device name and password is added.
• User interface DUT Escort (RS485, Bluetooth) is updated.

• Switching to the Device tab when connecting remotely is fixed.
• Error in receiving advertising packets in Bluetooth scanner for Galileosky 10 is fixed.
• Downloading the archive when connected via bluetooth is fixed.

• The GSMAUTH command, which allows you to configure the type of authentication in the GSM network is added.
• Bootloader 3.0 is added.

• Registration in some LTE networks is fixed.
• Registration in a GSM network is improved

• Support for Galileosky 10 device is added
• New firmware 1.0 for devices Galileosky 10 is added.
• New firmware 27.9 for devices Galileosky 7.0, OBD-II is added.
• New firmware 27.10 for devices Galileosky BaseBlock is added.
• New firmware 38.21 for devices Galileosky 7x is added.
• New firmware 46.0 (beta-version) for devices Galileosky 7x is added.
• Possibility to disable the message bus in the System section is added.
• The window for selecting the device to connect is redesigned.
• Displaying graphs on the CAN scanner tab is now available.
• Registering a tracker to the remote configuration service when connected through USB is added.
• SemaphoreTake and SemaphoreGive functions were added to EasyLogic.
• "Acquire semaphore" and "Release semaphore" blocks were added to the Easy Logic tab.
• Function "GetUserArray" to get data from the user's array is added in EasyLogic scripts.

• Sending a minor version of the firmware to the remote configuration server is added.

• WebDav operating is improved.

• WebDav features are disabled by default.

• WebDav operating is improved.

• The GSMAUTH command, which allows you to configure the type of authentication in the GSM network is added.
• Possibility to disable the message bus to save RAM resources is added.
• Function ChargerEnable is added in EasyLogic scripts.
• Upload of the client archive from the hub is improved.
• WebDav, Message Bus and Bluetooth configuration features are disabled by default.
• Transmission of the 0x49 tag to the Galileosky protocol, the place where it is uploaded (server\hub), the channel through which it is uploaded (GSM\WiFi) is added.
• The NODOUBLEPACK command that allows you to disable uploading the archive to the hub if it was sent to the main server is added.
• Dedicated virtual COM port for receiving diagnostic messages is added.
• SD/eMMC is available as a Flash Drive when the device is plugged into a computer.

• Error in switching to local device configuration when connecting remotely is fixed.
• Error in connecting to the device for Bluetooth configuration is fixed.

• Display of the marketing name when connecting to the device remotely is fixed.
• Display of GSM-related settings for Galileosky V7X.1.8, V7X.1.81, V7X.1.82, V7X.1.83, V7X.1.51, V7X.1.52 and V7X.1.53 trackers is fixed.

• New firmware 27.7 for devices Galileosky 7.0, OBD-II is added.
•  New firmware 27.8 for devices Galileosky BaseBlock is added.
• New firmware 44.5 (release-candidate) for devices Galileosky 7x is added.
• New firmware 45.0 (beta-version) for devices Galileosky 7x is added.
• The option to connect and configure trackers via Bluetooth is added.
• Run event and Incoming event blocks added to the Easy Logic tab.
• New user interface - Modbus TCP server.
• New user interface - Escort FLS (RS485, Bluetooth).

• Scaling of controls on screens with different DPI is fixed.

• CAN tag settings for Galileosky OBD-II devices is fixed.
• Program crash during Ins/Outs remote setting is fixed.

• If incorrect connection identifier is passed to SendAnswer function the answer will be sent to Configurator.

• Registration in some LTE networks is fixed.

• If incorrect connection identifier is passed to SendAnswer function the answer will be sent to Configurator.
• Loading of string parameters from the device's configuration is fixed.

• Bluetooth Low Energy is added API in Easy Logic.
• Configuring via Bluetooth is implemented.
• Support for up to 3 simultaneous Bluetooth Low Energy connections is added.
• Command to get BLE MAC address is added.
• «Run event" and "Incoming event» blocks added to Easy Logic.

• Parameter for setting the direction of reading IButton key ID bytes is added to IBCFG command.

• Parameter for setting the direction of reading IButton key ID bytes is added to IBCFG command.

• Listing of files on SD card via command FSLIST is fixed.
• Reboot of the device after executing commands via Bluetooth is fixed.
• Incorrect value of navigation time in the EGTS protocol is fixed.

•  Using RS232 port 1 when configuring Galileosky 7.0 devices is fixed.
• Protocol tag settings for Galileosky 7.0 devices are fixed.
• A list of supported RS232 equipment for Galileosky 7X instruments was fixed.
• Crash when connecting Galileosky V7X.4.1 devices is fixed.
• Device ID settings for Galileosky 7.0 devices are fixed.

• Upgrading to a firmware if it already exists in the device is fixed.

• Autoinformer sound is improved.
• Upgrading to a firmware if it already exists in the device is fixed.

• New firmware 33.15 (beta-version) for devices Galileosky 7x is added.
• New firmware 38.17 for devices Galileosky 7x is added.
• New firmware 44.2 (release-candidate) for devices Galileosky 7x is added.
• Drag&Drop upload is now available on the Files tab.
• Modules and features management was added as the Settings - System tab.
• Raw data packet length parameter to Bluetooth tags is added.
• Support for core, float, rational, fixed and string libraries in EasyLogic scripts is added.
• The block "SamplingPeriodFilter" on the "Filters" tab is added.

• The error of running the algorithm starting with the Incoming SMS block with ANY_TEXT filter is fixed.
• Program crash during Easy Logic script compilation is fixed.
• The settings loading feature for devices connected via USB was changed.

Automatic Allystar GNSS unit firmware upgrade is added.
Bootloader 2.5 is added.
Support for devices Galileosky V7X.4.x is added.
Firmware downloading is optimized.
Support for devices Galileosky V7X.1.83 is added.
Support for devices Galileosky V7X.1.25 is added.
Support for devices Galileosky V7X.0.86 is added.
Support for devices Galileosky V7X.1.53 is added.

•  Registration in Cat-M1 networks on devices with SIM7070G modem is fixed.
• Configuration loss made by newer firmwares is fixed.

• Script loading is improved.
• Support for devices Galileosky V7X.1.83 is added.
• Support for devices Galileosky V7X.1.25 is added.
• Support for devices Galileosky V7X.0.86 is added.
• Support for devices Galileosky V7X.1.53 is added.

• Reboot of the device when the SD card initialization failed is fixed.
• The error of running the algorithm starting with the Incoming SMS block with ANY_TEXT filter is fixed.
• The LED indication of the GNSS unit status is fixed.

• New entry containing milliseconds is added into galileosky protocol.
• The ENABLEARCHIVE command has been added, which allows you to disable the regular recording of archive points, while it remains possible to record a point from the Easy Logic algorithms.
• A new entry has been added to the galileosky protocol containing the reason for recording the archive point.
• Processing of 1-Wire keys for DS1991, DS1992 and DS1993 devices are added.
• iButton64 tags transmission has been added to the galileosky protocol.
• The USERSPEC command has been added, which allows you to disable the functional modules of the firmware to free up RAM.
• Support for the "SamplingPeriodFilter" block in filters is added.
• The number of supported polygonal geofences is increased to 1000000.
• Support for devices Galileosky V7X.1.83 is added.
• Support for devices Galileosky V7X.1.25 is added.
• Support for devices Galileosky V7X.0.86 is added.
• Support for devices Galileosky V7X.1.53 is added.
• Support for devices Galileosky V7X.4.x is added.

• The LED indication of the GNSS unit status is fixed.
• Writing data to tags from a bluetooth device with different lengths of advertising packets is fixed

• New firmware 38.15 for devices Galileosky 7x is added.
• New firmware 44.0 (release-candidate) for devices Galileosky 7x is added.
• New firmwares 25.17, 27.5 for devices Galileosky BaseBlock, 7.0 are added.
• Support for UDP protocol for connecting to monitoring servers is added.
• Support for TLS\SSL to connect to monitoring servers is added.
• Support for UDP and SSL in SockectOpen function is added.
• Functions SetLed and RegularLedEnable are added in EasyLogic scripts.
• Functions IridiumGetMtmsn and IridiumGetMomsn are added in EasyLogic scripts.
• Tooltips to the command parameters on the «Settings» tab is added.

• Operation of the autoinformer is fixed.
• Registration in Cat-M1 networks on devices with SIM7070G modem is fixed.

• The WIFICHECKLEGACY command has been added to configure connection verification with the hub for Galileosky 7X WiFi devices.
• The REMOTECONFIGADDR command has been added to configure settings remote configuration.
• Invocation of RS485 handlers in EasyLogic for "Modbus" and "Modbus and FLS" peripheral is added.
• Functions SetLed and RegularLedEnable are added in EasyLogic scripts.
• Support for UDP protocol for connecting to monitoring servers is added.
• Support for TLS\SSL to connect to monitoring servers is added.
• Support for UDP and SSL in SockectOpen function is added.
• Extended information about Easy Logic scripts is added (SCRIPTINFO command).
• Stability of the script loading is improved.
• Authorized phone number maximum length is Increased up to 20 symbols.

• Stability of the script loading is improved.

• Functions IridiumGetMtmsn and IridiumGetMomsn are added in EasyLogic scripts.
• Processing of 1-Wire keys for DS1991, DS1992 and DS1993 devices are added.
• The format of the response to the command via the Iridium modem is changed.
• Stability of the script loading is improved.

• RAM usage is optimized.

• Stability of the script loading is improved.

• Operating with RS-232, RS-485 configured for two stop bits is fixed.

• Processing of 1-Wire keys for DS1991, DS1992 and DS1993 devices are added.
• Stability of the script loading is improved.

• Operating with RS-232, RS-485 configured for two stop bits is fixed.
• RAM usage is optimized.

• Program crash during canceling settings loading is fixed.
• Error of the update downloading is fixed.
• Error of the configuration downloading for devices Galileosky OBD-II is fixed.
• Error when uploading data to the server on the «Data» tab is fixed.

• Support for devices Galileosky BaseBlock V1.0.30 is added.

• Operation of the autoinformer is fixed.
• Registration in Cat-M1 networks on devices with SIM7070G modem is fixed.

• Support for devices Galileosky V7X.4.x is added.

• New firmware 38.13 for devices Galileosky 7x are added.
• New firmware 43.3 (beta-versions) for devices Galileosky 7x are added.

• Output of diagnostic messages in Russian from EasyLogic scripts on the Diagnostics tab is fixed.

• New firmware 25.16 for devices Galileosky BaseBlock, 7.0 is added.
  New firmware 27.4 (beta-version) for devices Galileosky BaseBlock, 7.0 is added.

• Reboot of the device when receiving data from Wiegand 26 with an SD card inserted is fixed.
• Upload of static archive is fixed.
• Sending of zero coordinates via the Iridium unit at the start of the device is fixed.

• Support for devices with Allystar GNSS unit is added.
• Support for two-way communication via Iridium unit is added.
• Functions IridiumEnable, IridiumELMode, IridiumReceive, IridiumTransmit, IridiumGetCntMsgToTransmit are added in EasyLogic scripts.
• Launch of EasyLogic scripts for receiving Iridium Ring Alert is added.
• Sending archive points via Iridium unit if the transmission timeout is 0 is disabled.
• Processing of parameters in the block "Run command" of EasyLogic is added

• Reboot of the device when receiving data from Wiegand 26 with an SD card inserted is fixed.

• Reboot of the device when receiving data from Wiegand 26 with an SD card inserted is fixed.
• Upload of static archive is fixed.

• Reboot of the device when receiving data from Wiegand 26 with an SD card inserted is fixed.

•  New version of remote control service is implemented:

• Remarks on interaction with the remote control service is fixed

• Downloading CAN tag settings on the "CAN Scanner" tab is fixed.
• Program crash during Easy Logic script compilation is fixed.
• Using special characters in algorithms' names on "Filters" and "EasyLogic" tabs is restricted.

• Downloading CAN tag settings on the "CAN Scanner" tab is fixed.
• Program crash during Easy Logic script compilation is fixed.
• Using special characters in algorithms' names on "Filters" and "EasyLogic" tabs is restricted.

• Downloading CAN tag settings on the "CAN Scanner" tab is fixed.
• Program crash during Easy Logic script compilation is fixed.
• Using special characters in algorithms' names on "Filters" and "EasyLogic" tabs is restricted.

• Modem operation on Galileosky V7X.1.81 devices is fixed.

• New firmwares 32.18, 38.11 for devices Galileosky 7x are added
• New firmwares 39.9, 40.6, 41.5, 42.2, 43.1 (beta-versions) for devices Galileosky 7x are added

• Incorrect opening files in the CAN-loger is fixed
• Bluetooth tags setting on the "Settings" tab is fixed

• Actions in EasyLogic "Get bytes from user array" and "Copy bytes to user array" are fixed

• Variables containing driving style are added in Easy Logic.
• Possibility to resize the script editor window is added in Easy Logic.
• Support for binary operations in formulas on the CAN Scanner tab is added.
• Option to write masks to CAN tags on the CAN Scanner tab is added.
• New firmware 25.15 for devices Galileosky Base Block, 7.0 is added.
• New firmware 27.3 (beta-version) for devices Galileosky Base Block, 7.0 is added.
• New firmwares 32.17, 38.10 for devices Galileosky 7x are added.
• New firmwares 33.12, 39.8, 40.5, 41.4, 42.1, 43.0 (beta-versions) for devices Galileosky 7x are added.

• Incorrect saving of the TarFilter in the «Filters» tab is fixed.
• CAN-loger operating is improved.

• ENCALG command to change GSM and GPRS encryption mode for Telit modem is added.
• Corrections:
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Launching multiple «Should make photo» handlers in Easy Logic is fixed.
• Cyclic restart of device with Iridium modem due to low battery is fixed.
• Reading corrupted KML files is fixed.

• Launching multiple «Should make photo» handlers in Easy Logic is fixed.
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Reading corrupted KML files is fixed.

• Actions in Easy Logic «Get bytes from user array» and «Copy bytes to user array» are fixed.
• The maximum waiting time for registration in the GSM network has been increased to 2 hours.
• The speed of downloading archive via Configurator is increased.
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Downloading scripts on Galileosky 7x C devices is fixed.
• Receiving data using protocol Wiegand26 from devices connected to inputs 2 and 3 is fixed.
• Reading corrupted KML files is fixed.

• Bootloader 2.3 is added.
• Support for devices Galileosky V7X.1.52 and Galileosky V7X.1.82 is added.

• The maximum waiting time for registration in the GSM network has been increased to 2 hours.

• Support for devices Galileosky V7X.1.52 and Galileosky V7X.1.82 is added.
• Support for mask in CAN tags is added.

• Actions in Easy Logic «Get bytes from user array» and «Copy bytes to user array» are fixed.
• The maximum waiting time for registration in the GSM network has been increased to 2 hours.
• The speed of downloading archive via Configurator is increased.
• Launching multiple "Should make photo" handlers in Easy Logic is fixed.
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Receiving data using protocol Wiegand26 from devices connected to inputs 2 and 3 is fixed.
• Reading corrupted KML files is fixed.

• Support for devices Galileosky V7X.1.52 and Galileosky V7X.1.82 is added.
• Support for mask in CAN tags is added.

• Actions in Easy Logic «Get bytes from user array» and «Copy bytes to user array» are fixed.
• The maximum waiting time for registration in the GSM network has been increased to 2 hours.
• The speed of downloading archive via Configurator is increased.
• Launching multiple "Should make photo" handlers in Easy Logic is fixed.
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Receiving data using protocol Wiegand26 from devices connected to inputs 2 and 3 is fixed.
• Reading corrupted KML files is fixed.
• Allystar unit invalid coordinates is fixed.

• Support for devices Galileosky V7X.1.52 and Galileosky V7X.1.82 is added.
• Support for mask in CAN tags is added.

• Actions in Easy Logic «Get bytes from user array» and «Copy bytes to user array» are fixed.
• The maximum waiting time for registration in the GSM network has been increased to 2 hours.
• The speed of downloading archive via Configurator is increased.
• Launching multiple "Should make photo" handlers in Easy Logic is fixed.
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Receiving data using protocol Wiegand26 from devices connected to inputs 2 and 3 is fixed.
• Reading corrupted KML files is fixed.
• Allystar unit invalid coordinates is fixed.

• Support for devices Galileosky V7X.1.52 and Galileosky V7X.1.82 is added.
• Data stored in ROM is isolated for each Easy Logic script.
• Support for mask in CAN tags is added.

• Actions in Easy Logic «Get bytes from user array» and «Copy bytes to user array» are fixed.
• The maximum waiting time for registration in the GSM network has been increased to 2 hours.
• The speed of downloading archive via Configurator is increased.
• Launching multiple "Should make photo" handlers in Easy Logic is fixed.
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Receiving data using protocol Wiegand26 from devices connected to inputs 2 and 3 is fixed.
• Reading corrupted KML files is fixed.
• Allystar unit invalid coordinates is fixed.

• Support for devices Galileosky V7X.1.52 and Galileosky V7X.1.82 is added.
• Variables containing driving style are added in Easy Logic.
• Data stored in ROM is isolated for each Easy Logic script.
• Support for mask in CAN tags is added.

• Actions in Easy Logic «Get bytes from user array» and «Copy bytes to user array» are fixed.
• The maximum waiting time for registration in the GSM network has been increased to 2 hours.
• The speed of downloading archive via Configurator is increased.
• Launching multiple "Should make photo" handlers in Easy Logic is fixed.
• Parsing of the alphanumeric address of the SMS sender is fixed.
• Receiving data using protocol Wiegand26 from devices connected to inputs 2 and 3 is fixed.
• Reading corrupted KML files is fixed.
• Allystar unit invalid coordinates is fixed.

• Support for devices Galileosky V7X.1.52 and Galileosky V7X.1.82 is added.
• Variables containing driving style are added in Easy Logic.
• Amount of simultaneous connections to the Wi-Fi hub is increased up to 3.
• Data stored in ROM is isolated for each Easy Logic script.
• Support for mask in CAN tags is added.
• Autoinformer out is always on when playing an audio file.

• Possibility to configure bands on devices with SIM7070G modem is added.
• Possibility to change Bluetooth device name is added.
• MODBUS  tags on the Filters tab is available.
• New firmware 25.14 for Galileosky BaseBlock and 7.0 devices is added.
• New firmware 27.2 (beta-version) for Galileosky BaseBlock and 7.0 devices is added.
• New firmwares 32.16, 38.9 for Galileosky 7x devices are added.
• New firmwares 33.11, 39.7, 40.4, 41.3, 42.0 (beta-versions) for Galileosky 7x devices are added.

• Escort TH BLE sensor parameters parsing is fixed.

• Processing of SMS received from the alphanumeric address of the sender is added.

• The launch of chains starting with RS485 Handler event and contained in different scripts is fixed.

• Processing of SMS received from the alphanumeric address of the sender is added.

• Server connection hang-up when operating with some mobile network operators on devices with SIM800C modems is fixed.
• The launch of chains starting with RS485 Handler event and contained in different scripts is fixed.

• Possibility to configure bands on devices with SIM7070G modem is added.

• Escort TH BLE sensor parameters parsing is fixed.
• The launch of chains starting with RS485 Handler event and contained in different scripts is fixed.
• Scanning of BLE devices is improved.
• The LED indication of the Wi-Fi module status was fixed.

• Possibility to configure bands on devices with SIM7070G modem is added.

• Possibility to configure bands on devices with SIM7070G modem is added.
• New types of objects (Bus, Train) are added in coordinate filtering.

• Escort TH BLE sensor parameters parsing is fixed.
• The launch of chains starting with RS485 Handler event and contained in different scripts is fixed.
• Scanning of BLE devices is improved.
• The LED indication of the Wi-Fi module status was fixed.

• Support for Galileosky V7X.1.22 and Galileosky V7X.1.81 devices is added.
• Support for operators: bitwise AND (&), bitwise OR (|), bitwise XOR (^), remainder (%), bitwise left shift (<), bitwise right shift(>) is added to CAN filters formula.
• Diagnostic messages about the reason of powering off of GSM, GNSS, WIFI units and SD card.
• iButton and MODBUS tags are available for writing in EasyLogic.
• MODBUS tags are available in filters.
• Possibility to change Bluetooth device name is added.

• Self-diagnostic criteria for automatic rebooting was fixed:
• The Ctrl+Enter (Numpad) key combination to send the current command in the "Commands" tab was added.
• The firmware versions 32.15, 38.8 for Galileosky 7X were added.
• The firmware versions 33.10, 39.6, 40.3, 41.2 (beta) for Galileosky 7X were added.

• The error in displaying the satellite information on the "Device" tab for Galileosky Base Block, 7.0 and OBD-II tracking devices was fixed.
• The error during the operation with the calibration table block on the "Filters" tab was fixed.

• V7X.1.22 and Galileosky V7X.1.81 support was added.
• SMS processing, received from alphanumeric sender's address was added.

• The archive clearing on the SD card was added.
• The WebDAV data uploading using Wi-Fi connection was fixed.
• The incorrect result of the WIFIMAC command was fixed.
• The directory deletion was fixed.
• The connection hang-up during connection to the server for some mobile operators on the tracking devices with the SIM800C modems was fixed.
• The network registration with some mobile operators on the Galileosky 7X LTE tracking devices was fixed.

• Galileosky V7X.1.22 and Galileosky V7X.1.81 support was added.

• Galileosky V7X.1.22 и Galileosky V7X.1.81 support was added
• SMS processing, received from alphanumeric sender's address was added.

• The archive clearing on the SD card was added.
• The WebDAV data uploading using Wi-Fi connection was fixed.
• The incorrect result of the WIFIMAC command was fixed.
• The directory deletion was fixed.
• The SD card formatting with the exFAT file system was fixed.
• The use of the LBS as a coordinate source was fixed.
• The connection hang-up during connection to the server for some mobile operators on the tracking devices with the SIM800C modems was fixed.
• The network registration with some mobile operators on the Galileosky 7X LTE tracking devices was fixed.

• Galileosky V7X.1.22 и Galileosky V7X.1.81 support was added.
• SMS processing, received from alphanumeric sender's address was added.
• The advanced coordinate filtering system was added.

• The archive clearing on the SD card was added.
• The WebDAV data uploading using Wi-Fi connection was fixed.
• The incorrect result of the WIFIMAC command was fixed.
• The directory deletion was fixed.
• The SD card formatting with the exFAT file system was fixed.
• The use of the LBS as a coordinate source was fixed.
• The connection hang-up during connection to the server for some mobile operators on the tracking devices with the SIM800C modems was fixed.
• The simultaneous operation with several 1-wire devices was fixed.
• The network registration with some mobile operators on the Galileosky 7X LTE tracking devices was fixed.

• The firmware versions 32.14, 38.7 for Galileosky 7X were added.
• The firmware version 27.1 (beta) for Galileosky BaseBlock, 7.0, OBD-II was added.
• The firmware versions 33.9, 39.5, 40.2, 41.1 (beta) for Galileosky 7X were added.

• The error of sending saved configuration during remote configuration was fixed.

• Self-diagnostic criteria for automatic rebooting was fixed.

• Galileosky V7X.0.82 support was added.

• Galileosky V7X.0.82 support was added.

• Self-diagnostic criteria for automatic rebooting was fixed.

• The ability to configure the transmission of parameters via the J1979 protocol on the CAN Scanner tab was added. Instead of polling 45 parameters, which takes about a minute, and the lack of visual representation of the received data, the client will be able to see the received data at once and mark only the needed ones for sending to the server.
• Added firmware 32.13 and 38.6 for Galileosky 7X devices.
• Added firmware 33.8, 39.4, 40.1 and 41.0 (beta versions) for Galileosky 7X devices.

• Fixed display of variable descriptions on the Filters and Easy Logic tabs on systems with a language other than Russian and English.
• The built-in database in the CAN Scanner is updated.

• Support for Galileosky V7X.1.8, Galileosky V7X.0.83 tracking devices was added.
• Automatic firmware update older than 34 with bootloader update using UPGRADE X command (X=0 or greater than 33) was added. Instead of 4 successive steps of one tracking device update (update to 33 firmware, double upgradebl command, update to X firmware) with obligatory control after each step, it became possible to use only 1 step with single command update. This should ease the process of upgrading the bootloader and the transition to older firmware.

• Fixed the Driving style tag value when using accelerometer as a data source.

• Support for Galileosky V7X.1.8, Galileosky V7X.0.83 devices was added.

• Fixed the Driving Style tag value when using accelerometer as data source.
• Fixed Modbus operation in ASCII mode.
• Improved stability of Modbus device register values.

• ROMDelete, ROMRead, ROMWrite, ROMErase functions have been added to Easy Logic. Easy Logic algorithms now can store operation settings and counters in script language in the device memory to protect against discarding on reset.
• Added possibility to configure the parameters of J1979 .
• The speed of unloading the internal archive to the hub was increased. To transfer from the client to the hub the data are pre-archived, which significantly increases the speed of point transfer and reduces the exchange time.
• Processing of parameters in the Execute command EasyLogic block was added.
• Support for Galileosky V7X.1.8, Galileosky V7X.0.83 was added.

• Self-troubleshooting tab to control for trigger criteria is added.
• Information about self-troubleshooting on the Device tab is added.
• Variables containing progress of a client's archive uploading to the hub are added to Easy Logic.
• RAMErase, RAMRead and RAMWrite functions are added to Easy Logic.
• New firmware 25.13 for Galileosky BaseBlock and 7.0 devices is added.
• New firmware 27.0 (beta-version) for Galileosky BaseBlock and 7.0 devices is added.
• New firmwares 32.12 and 38.5 for Galileosky 7x devices are added.
• New firmwares 33.7, 39.3, 40.0 (beta-versions) for Galileosky 7x devices are added.
• Possibility to choose a satellite navigation system on the Track tab for Galileosky BaseBlock and 7.0 devices is added.

• Error displaying a context menu in the device information window is fixed.
• Program crash during Geofence row deleting for Galileosky 2.3 is fixed.

• Uploading internal archive stuck is fixed.

• Possibility to choose a satellite navigation system is added.
• Information about satellites is added (SATINFOEXT command).
• Self-troubleshooting feature is added.
• Mileage accuracy at high values is increased.

• Scanning of BLE devices is improved.

• Operation with APN on Galileosky 7X LTE devices is fixed.
• Uploading internal archive stuck is fixed.
• Incorrect RSSI tag value is fixed.
• Checking connection to the hub is fixed.
• Retrieving coordinates via LBS for modem SIMCom 7500E is fixed.

• Support for Galileosky 7X.1.8 is added.
• Bootloader version is added to the response of SOFTVERSION command.

• Operation with APN on Galileosky 7X LTE devices is fixed.

• Device self-troubleshooting is added.
• Support for sockets in EasyLogic over WiFi connection is added.
• Variables containing progress of a client's archive uploading to the hub are added in EasyLogic.
• Scanning of BLE devices is improved.
• RAMErase, RAMRead, RAMWrite functions are added in EasyLogic scripts.
• Automatic baud rate detection for weight indicator Tenzo-M is added.
• Mileage accuracy at high values is increased.

• Received value multiplication by 100 for int32 MODBUS registers is removed.

• The support of Galileosky 7X.1.8 devices has been added.
• It is possible to set a random speed of the CAN bus on the CAN Scanner tab.
• 25.12 firmware for Galileosky Base Block, 7.0. has been added.
• 32.11, 38.4 firmware for Galileosky 7X has been added.
• 39.2 (beta-version) firmware for Galileosky 7X has been added

• The scaling of the Navigation Data on the Device tab has been fixed.

• The flash memory chip detection bug has been fixed.

• The call hangup with a push-to-talk button has been fixed.

• Wi-Fi network search bug has been fixed.

• The tracking device reboots when selecting a large buffer using the Easy Logic script PortInit function has been fixed.
• The incorrect saving of the Hub client data to another client directory has been fixed.
• The Wi-Fi module hangup has been fixed.
• The call hangup with a push-to-talk button has been fixed.
• A prohibition on connecting to third-party servers has been added if the device is connected to the Hub.

• Wi-Fi network search bug has been fixed.
• The tracking device reboots when selecting a large buffer using the Easy Logic script PortInit function has been fixed.
• The incorrect saving of the Hub client data to another client directory has been fixed.
• The Wi-Fi module hangup has been fixed.
• The incorrect tags saving when using random data transfer from BLE advertising package has been fixed.
• The call hangup with a push-to-talk button has been fixed.
• A prohibition on connecting to third-party servers has been added if the device is connected to the Hub.

• Galileosky 7X.3.0 tracking devices support was added.

• The firmware 25.11 for Galileosky BaseBlock, 7.0 tracking devices was added.
• The firmware 32.10 for Galileosky 7X was added.
• Firmware versions 33.6, 32.10, 37.4, 38.3, 39.1 (beta) for the Galileosky 7X tracking devices were added.

• The error when copying the CAN bus function blocks in EasyLogic was fixed.
• The gap error in script compilation in EasyLogic for SetVar/GetVar/GetVarAddr functions was fixed.

• The work with the mobile operator code lists was improved.

• Galileosky V7X.3.0 tracking devices support was added.
• Bootloader 2.2 was added.
• The battery voltage check during the bootloader upgrade was fixed.

• The battery voltage check during the bootloader upgrade was fixed.

• Galileosky V7X.3.0 tracking devices support was added.

• The work with the mobile operator code lists was improved.
• The automatic CAN bus speed detection was fixed compared to the previous version.
• The gap error in script compilation in EasyLogic for SetVar/GetVar/GetVarAddr functions was fixed.

• The protocol of the Technoton BLE fuel level sensor has been developed. The manufacturer information in the protocol was updated for the correct parsing of the received message (Firmware 32.9, Firmware 37.3, Firmware 38.2).
• The initial data of the Advertise BLE packet is displayed on the Bluetooth tab. It is possible to work with the Advertise packets of any BLE device. The source data is obtained and written to variables (Configurator 4.25.04, Firmware 39.0).
• Convenience of working on the Easy Logic tab. When the free field of Easy Logic is clicked on, the selection will be removed from the blocks and other tabs. (Configurator 4.25.04).
• It is possible to refer to the address of a variable instead of its name. This makes it possible to cycle through variables knowing their address in memory. It makes it easier to work with a large number of variables in memory (Configurator 4.25.04).

• Transmission of incorrect data to the server, when there is no connection with the Datacold500 device. It has been fixed according to suggested changes (Firmware 23.25, Firmware 25.10, Firmware 32.9, Firmware 37.3, Firmware 38.2).
• The WEP encryption does not connect to the Wi-Fi network.
• The WEP encryption support has been restored (Firmware 32.9, Firmware 37.3, Firmware 38.2).
• The port buffer allocation error in Easy Logic. The behavior of the port initialization bug with a large buffer was corrected. The tracking device continues to work in normal mode (Firmware 23.25, Firmware 25.10, Firmware 32.9, Firmware 37.3, Firmware 38.2).
• Remote script upload bug. Changes were made, the problem was fixed (Firmware 23.25, Firmware 25.10, Firmware 32.9, Firmware 37.3, Firmware 38.2).
• The incorrect length header of compressed extended protocol. The further data length header was corrected in the extended compressed protocol (Firmware 32.9, Firmware 37.3, Firmware 38.2).
• The voice functions of the module are not restored after the modem power is turned off. It requires restarting the device. the inclusion of all disable modem functionality was corrected if the device is not powered. Now the restart of the device is not required (Firmware 32.9, Firmware 37.3, Firmware 38.2).
• The 2 CAN interface configuration for the Galileosky 7x LTE tracking device is not displayed. The full display of settings was restored (Configurator 4.25.04).
• The BLE tagging protocol for Galileosky 7x LTE bug. The ability to mark tags in the protocol was corrected (Configurator 4.25.04).
• Saving variables in Easy Logic bug. The bug of saving a variable in blocks when saving an algorithm was fixed (Configurator 4.25.04).
• The Settings tab for Galileosky 7x LTE Wi-Fi does not show the RS-485 interface. Display was restored (Configurator 4.25.04).
• The configurator interface does not fit on the screen at a resolution below 1600*900. The improvements to the interface were made. Now the buttons will be placed in two rows at a lower resolution and screen size (Configurator 4.25.04).
• Copying variables in blocks of Easy Logic algorithms bug. The copying process was fixed (Configurator 4.25.04).

• Se agregaron las versiones de firmware 31.11, 32.8 para los dispositivos de rastreo Galileosky 7X.

• Se agregaron las versiones de firmware 33.5, 37.2, 38.1 (beta) para los dispositivos de rastreo Galileosky 7X.

• Se ha solucionado el envío incorrecto de puntos con las coordenadas negativas en la pestaña «Datos».

• Se ha solucionado el retraso en la visualización de datos en la pestaña «Dispositivo».

• The statistics of points in the internal archive has been fixed.

• The time synchronization via GSM on the Galileosky 7X LTE tracking devices has been fixed.

• The statistics of points in the internal archive has been fixed.

• Ability to determine the CAN bus parameters using the local database. In the Configurator there is a built-in CAN database for more than 200 units of equipment. To use this functionality, just open the CAN Scanner tab, select the make, model and year of manufacturing of the vehicle and get a list of available data for parsing immediately.  Then it is enough to specify in what tags they should be written and click the "Apply" button. (Configurator 4.25.02, Firmware 7x v38)

• Ability to save and upload the Easy Logic agorithms bin files. It is now possible to get a bin file of any algorithm and upload it to the tracking device. This will allow to share the algorithm for further use without disclosing the source code (Configurator 4.25.02, Firmware 7x v38)

• Configure the addresses of the servers for downloading scripts and firmware updates directly in the Configurator in the firmware. It is now possible to use your own servers to download the firmware and Easy Logic algorithms. To do this, you need to deploy your own server and integrate the protocol into it. (Configurator 4.25.02, Firmware 7x v38)

• Get Easy Logic geographical coordinates. The functionality of the variable substitution in the "Send answer" block was fixed. (Configurator 4.25.02, Firmware 7x v38, Firmware 7x v36.3, Firmware 7x v32.7)
• Incorrect operation of the filters tab when saving the algorithm with the calibration table. The errors when saving and loading filters were fixed (Configurator 4.25.02, Firmware 7x v38, Firmware 7x v36.3, Firmware 7x v32.7)
• Problem with displaying the Configurator audio converter functionality. Scrolling was added to the interface so that it was possible to use all the functionality of the audio converter of the configurator at a low resolution (Configurator 4.25.02, Firmware 7x v38, Firmware 7x v36.3, Firmware 7x v32.7)
• If an attempt to add a tracking device to a remote configuration account fails, the IMEI of the tracking device is displayed (Configurator 4.25.02, Firmware 7x v38, Firmware 7x v36.3, Firmware 7x v32.7)
• The "Set geo data" block sets the year to 2070. The year setting in the "Set geo data" Easy Logic block was fixed. It sets the year 2000 (Configurator 4.25.02, Firmware 7x v38, Firmware 7x v36.3, Firmware 7x v32.7)

• Notification via SMS and calls in the event of a detection alarm was fixed.
• The maximum length of the response to the remote configuration server commands has increased.

• Automatic switching to internal coordinate source was fixed.

• Automatic switching to internal coordinate source was fixed.
• Stability of work with SD cards is improved.
• Low voltage sleep was fixed.

• Automatic switching to internal coordinate source.
• WIFI_CONNECTED TO HUB status update was fixed.
• Stability of work with SD cards is improved.
• Low voltage sleep was fixed.

• New firmware: stable 24.19, stable 26.04, release candidate 28.02, beta 30.0, beta 31.00, beta 30.02, beta 31.01 for Galileosky 7x units.
• New switch SIM-cards from EasyLogic function.
• New "Sound" tab to control auto answer for units with GSM module.
• New 232.2 firmware for Galileosky 5.0 devices.
• New firmware: stable 23.16, beta 25.00 for Galileosky 7 and Galileosky Base Block devices.

• Improved archive unloading from SD-card.

• Improved "Filters" tab work.
• Corrected messages receiving in the CAN module.

• Autoinformer performance with negative coordinates is more stable now.
• Optimized GSM performance.
• Corrected archive data sending on SD card to an additional server.
• Better sending of tire pressure data.
• Improved work with SD cards.
• Improved hub-to-hub connection when prohibiting data uploads over the cellular network.

• New ability to switch between SIM-cards from EasyLogic.
• Improved diagnostic subsystem.
• New RS485 operation mode "FLS and Modbus".

• Optimized GSM performance.

• Optimized operation of serial interfaces.
• Improved autoinformer performance with negative coordinates.
• Corrected sending of archive data on SD card to an additional server.
• Improved hub-to-hub connection when prohibiting data uploads over the cellular network.
• Improved work with SD cards.
• Corrected tire pressure data sending.

• Corrected notification via SMS and calls when an alarm is triggered.

• The maximum length of the response to the commands of the remote configuration server has been increased.

• Better autoinformer performance with negative coordinates has been corrected.
• Optimized GSM performance.
• Improved hub-to-hub connection when prohibiting data uploads over the cellular network.
• Improved archive data sending on SD card to additional server.
• Optimized sending of tire pressure data.

• Improved diagnostic subsystem.
• Added the ability to disable file system journaling on SD.
• Added read-only mode for SD card.

• Better autoinformer performance with negative coordinates has been corrected.
• Optimized GSM performance.
• Improved hub-to-hub connection when prohibiting data uploads over the cellular network.
• Optimized sending of archive data on SD card to an additional server.
• Improved tire pressure data sending.